Bush - Gear Stick / Lever - Remote Change - Mini

Bush for gear stick in Remote change gearbox. Gear lever to selector toggle. This normally wears out resulting in a gear stick that rattles. Vehicle: Mini 22G389  

Bush - Magic Wand Gear Stick (850)

Bush to fit 'Magic Wand' gear lever as fitted to Morris 850 Minis.

Engine Mount - Automatic (Converter End) - Mini

Lower engine mount to suit Automatic Mini models such as Morris mini.matic. Fits converter end. See 22A1018 for other mount. 22A917

Engine Mount - Automatic (Radiator End) - Mini

Lower engine mount to suit Automatic Mini models such as Morris mini.matic. Fits radiator end. See 22A917 for other mount. 22A1018

Engine Mount - Lower - Mini/Moke

Lower engine mount. Fitment: - Mini & Moke, left or right side, 2 required per vehicle. Does not fit Automatic models. - Morris 1100, clutch end (1 required). Use with 2A305. 21A1902

Engine Mount - Lower, with Captive Nuts - Mini/Moke

Lower engine mount to suit Mini & Moke. Has captive nuts to make it easier to fit. Suits left or right side (manual transmission only). Vehicle: Mini / Moke / Morris 1100 21A1902CAP

Gear Shift Boot - Mini

Rubber gear lever boot to suit all Australian Minis with Remote and Rod change gearbox. Does not suit Morris 850 and some Vans and Mokes. Model: Mini / Moke 22A608 / AYG3174  

Gear Shift Boot - Moke (early)

Rubber gear lever boot to suit early model Mokes up until 1975 (pre rod change). For later models see part 22A608. Vehicle: Moke HYK2568

Gear Shift Boot - Morris Mini 850 (Magic Wand)

Rubber gear shift boot to suit Morris Mini 850 with 'Magic Wand' gear lever. This is the longer gear stick which comes out closer to the firewall. Also fitted to base model Mini Vans. All other Minis can use 22A608 for gear sticks between the seats...

Gear Shift Boot, on Gearbox - Morris 850

Rubber gear lever boot to suit Morris Mini 850 with 'Magic Wand' gear lever. Boot is fitted to gearbox to stop dirt entering. See 14A6860 for boot that goes on floor in cabin.

Gearbox Lower Steady Bar Kit - LH - Mini

Lower gearbox steady kit. Fits to left side of transmission on all rod change Mini models (1973 onwards). Replacement bushes are the same as top steady bushes - 2A5875. Vehicle: Mini MSSK001

Half Moon Front Plug - Remote Change - Mini

Front plug (half moon) for between Diff housing and Remote Gear Change housing fitted to Mini Cooper, Cooper S, Deluxe, Mini K and early Mini Clubmans (to around 1972). Vehicle: Mini 22A285

Mount - Remote Change - Rear - Mini

Mount for 'Remote Change' gearbox as fitted to Cooper S, Mini Deluxe, Cooper, Mini K and early Leyland Mini Clubman. Fits on the end of the gearchange housing. Vehicle: Mini 21A956

O Ring - Detent Plunger - Rod Change - Mini/Moke

O-Ring for detent plunger on drivers side differential side cover. Fitted to rod change gearboxes only. Vehicle: Mini/Moke 22G1417

Remote Change Bolt - Housing to Diff (Long) - Mini

Bolt (long) to attach extension housing to gearbox on Remote style transmissions as fitted to Mini Deluxe, Mini K, Cooper, Cooper S, Clubman GT and early Clubmans. Vehicle: Mini ZCS628

Remote Change Bolt - Housing to Diff (Short)

Bolt (short) to attach extension housing to gearbox on Remote style transmissions as fitted to Mini Deluxe, Mini K, Cooper, Cooper S, Clubman GT and early Clubmans. Cross reference: SH506081L

Remote Change Bush - Gear Stick (early Cooper)

Bush for gear stick in Remote change gearbox. Suits early model Cooper gearboxes. This normally wears out resulting in a gear stick that rattles.

Remote Change Nylon Retaining Flange

Split nylon retaining flange for remote change gearboxes (Mini). Located on gear lever tension spring. Model: Mini

Remote Change Selector Shaft Bush

Selector shaft bush fitted to diff housing on remote change gearboxes. Model: Mini / Moke

Remote Change Side Dust Plug [22A271]

Dust plug for the side of the Remote Gear Change housing fitted to Mini Cooper, Cooper S, Deluxe, Mini K and early Mini Clubmans (to around 1972). Vehicle: Mini 22A271

Reverse Light Switch - Mini/Moke/Midget

Reverse light switch to fit: - Mini & Moke with "Rod change" gearbox fitted (1974 onwards) - MG Midget 1500 GAE191A

Rod Change Detent Ball

Ball to sit behind the spring (22G2083) for detent plunger on drivers side differential side cover. Fitted to rod change gearboxes only.

Rod Change Detent Sleeve

Sleeve for detent plunger on drivers side differential side cover. Fitted to rod change gearboxes only. Use with BLS110 ball and 22G2083 spring.

Rod Change Detent Spring

Spring for detent plunger on drivers side differential side cover. The ball that sits behind is BLS110. Fitted to rod change gearboxes only.

Rod Change Dust Boot - Mini/Moke

Rubber dust seal boot for rod change Minis. Goes on before linkage is attached to the gear box. This prevents dust and dirt getting at the seal (AHU1672) and causing it to fail (and leak lots of oil!). Also see MSSK050 leak prevention kit. DAM3022

Rod Change Gear Box Selector Rod Seal - Mini/Moke

Seal goes around selector rod in gearbox of all Rod Change gearboxes fitted to Mini Clubmans from around 1973. You can actually fit 2 of these seals, one on top of the other. This is probably where your oil leak is coming from!!! AHU1672

Rod Change Gear Lever Locating Pin

Gear Lever locating pin, suits Rod Change gearboxes. Fits in the side of the housing to locate the gear lever. If this is worn it can cause excessive movement.

Rod Change Gear Lever Rod Eye

Rod eye to fit the gear stick in rod change gearboxes as fitted to late model Minis. When this is worn you get a very sloppy gear shift action.

Rod Change Gearbox - Nylon Cup Washer

This part is no longer available (NLA). Nylon cup washer for rod change gear lever. Sits below gear shift retainer. Use with AYG3261 spring (now NLA). Model: Mini

Rod Change Oil Leak Prevention Kit - Mini/Moke

Rod change leak prevention kit. Kit has an alloy sleeve with o-ring, seal (AHU1672) and a dust cover (DAM3022). The alloy sleeve supports the rod more effectively. To install: remove all old seals etc, insert alloy sleeve, then insert the seal. Put on...

Rod Change Selector Coupling - Mini/Moke

Selector yoke to suit rod change gearboxes as fitted to late model Mini and Moke models (1974 onwards). Use 2 x RPS1416 roll pins to fit. Vehicle: Mini / Moke 42H1116

Rod Change Selector Roll Pin - Mini/Moke

Gear change roll pin, suits Rod Change gearboxes. Goes in selector coupling (42H1116) to join gear shift rod to gearbox. Require two. These can often work loose and fall out meaning you can no longer select gears, so it is worthwhile replacing these...

Rod Change Steady Rod Bolt

Bolt to hold the steady bar/rod to the gearbox on Rod change Minis. Goes through the bush 13H7286.

Rod Change Steady Rod Bush - Mini/Moke

Steady bar bush for rod change transmission. Attachs to diff housing. Vehicle: Mini Clubman 13H7286

Roll Pin - Selector Fork 3rd/4th

Roll pin to secure the 3rd/4th gear selector to the selector shaft. Rod change gearboxes only.

Spring - Gear Stick / Lever - Mini/Minor/Sprite/Midget

Spring for gear stick / lever. Fitment: - Mini - Remote change gearbox, 1965 onwards. This normally breaks or is missing, resulting in a gear stick that rattles. - Morris Minor - 948cc/1098cc (with extension housing - not 803cc or sidevalve) - Austin...